Search Results (727)

Co-based amorphous wires (Co-AWs) are functional materials renowned for their high impedance change rate in magnetic fields and a pronounced giant magnetoimpedance (GMI) effect. In this study, magnetron sputtering (MS) and dip-coating (DC) techniques were employed to fabricate carbon-based nanocoatings aimed at modulating the GMI properties of Co-AWs. The magnetic properties and GMI responses of the composite Co-AWs with carbon-based coatings were comparatively analyzed. The results demonstrate that both methods effectively enhanced the GMI properties of the coated Co-AWs. The DC method emerged as a rapid and efficient approach for forming the coated film, achieving a modest enhancement in GMI performance (10% enhancement). In contrast, the MS technique proved more effective in improving the GMI effect, yielding superior results. Co-AWs coated via Ms exhibited smoother surfaces and reduced coercivity. Notably, the GMI effect increased with the thickness of the sputtered carbon coatings, reaching a maximum GMI effect of 522% (a remarkable 357% enhancement) and a sensitivity of 33.8%/Oe at a coating thickness of 334 nm. The observed trend in the GMI effect with carbon layer thickness corresponded closely to variations in transverse permeability, as determined by vibrating sample magnetometry (VSM). Furthermore, the carbon coating induced changes in the initial quenching stress on the surface of the Co-AWs, leading to alterations in impedance and a significant reduction in the characteristic frequency of the Co-AWs. Our findings provide valuable insights into the modulation of GMI properties in Co-AWs, paving the way for their optimized application in advanced magnetic sensor technologies. Full article

Transforming H₂O and CO₂ into solar fuels like syngas is crucial for future sustainable transportation fuel production. Therefore, the MgFe₂O₄/CO₂ splitting cycle was thermodynamically scrutinized to estimate its solar-to-fuel energy conversion efficiency in this investigation. The thermodynamic data required to solve the modeling equations were obtained using the HSC Chemistry program. The reduction non-stoichiometry was assumed to be equal to 0.1 for all computations. One of the study’s primary goals was to examine the impact of the inert sweep gas’s molar flow rate on the process parameters related to the MgFe₂O₄/CDS cycle. Overall, it was understood that the effect of the inert sweep gas’s molar flow rate on the thermal reduction temperature was significant when it increased from 10 to 40 mol/s compared to the rise from 40 to 100 mol/s. The energy needed to reduce MgFe₂O₄ increased slightly due to the surge in the inert sweep gas’s molar flow rate. In contrast, the energy penalty for heating MgFe₂O_4-δred from the re-oxidation to thermal reduction temperature significantly decreased. Including gas-to-gas heat exchangers with a gas-to-gas heat recovery effectiveness equal to 0.5 helped reduce the energy demand for heating the inert sweep gas. Overall, although the rise in the inert sweep gas’s molar flow rate from 10 to 100 mol/s caused a drop in the thermal reduction temperature by 180 K, the total solar energy needed to drive the cycle was increased by 85.7 kW. Accordingly, the maximum solar-to-fuel energy conversion efficiency (13.1%) was recorded at an inert sweep gas molar flow rate of 10 mol/s, which decreased by 3.7% when it was increased to 100 mol/s. Full article

Composite bipolar plates are a new class of material bipolar plates for PEMFCs. However, their application is limited by problems such as the difficulty of balancing their strength/conductivity properties. In this paper, by using surface-modified carboxylated short-cut carbon fibers and hydroxylated carbon nanotubes as well as PI resin, the interfacial bonding between the carbon-based filler and the resin is effectively improved under the premise of ensuring electrical conductivity, which enhances the flexural strength. The effect of the surface modification of the filler on the interfacial bonding between the filler and the PI resin is thoroughly investigated through molecular dynamics simulations. The mechanism for this improved bonding was also studied. Through the surface modification of the filler, the composite bipolar plates possessed a flexural strength of 49.06 MPa and a planar conductivity of 228.52 S/cm with the addition of 6% MWCNT-OH as well as 12% CCFs, which has the potential to be an optional substrate for composite bipolar plates. Full article

Here, crystalline SiO₂ quantum dots (QDs) of 3–5 nm size were grown within the layers of reduced graphene oxide (rGO) by a solution mode chemical growth process at a relatively low temperature (100 °C). The composite was applied as a negative electrode in a Li-ion half-cell battery and the electrochemical investigation confirmed a distinct first-cycle discharge/charge capacity (~865 mAhg⁻¹/387 @ 51 mAg⁻¹). The battery could retain a capacity of 296 mAhg⁻¹ after 60 charge/discharge cycles with 99% coulombic efficiency. Furthermore, at a high current rate of 1.02 Ag⁻¹, the battery was able to display an apparent rate capability (214.47 mAhg⁻¹), indicating the high chemical and mechanical stability of the composite at a high current rate. A structural analysis revealed clear distinct diffraction peaks of SiO₂ and high-resolution transmission electron microscopy images showed discrete atomic planes, thereby confirming the growth of crystalline SiO₂ QDs within the layers of rGO. Full article

Activated biomass has gained interest as an alternative to coal-based activated carbon (AC). This work investigates the environmental impact (EI) of coconut shell (CS)-derived AC as a substitute for non-renewable coal-based AC. The AC was produced in-house using tandem acid activation and pyrolysis, employing two activation pathways: sulfuric acid (H₂SO₄) and phosphoric acid (H₃PO₄). This study further investigates the impact of activation routes, fuel types, and water sources on environmental outcomes. This evaluation focuses on six key impacts: climate change, fossil depletion, freshwater ecotoxicity, freshwater eutrophication, land use, and energy net. The H₂SO₄ activation pathway is more favorable in terms of EI due to its lower net energy requirement (27.2 MJ) and reduced carbon emissions (1.2 kg CO₂ eq.). However, it requires 4.7 kg of AC to adsorb 1 kg of dye, whereas the H₃PO₄ pathway requires only 4.3 kg. Therefore, while the H₃PO₄ pathway may be preferred for applications needing higher adsorption capacities, the H₂SO₄ pathway offers a more environmentally benign option, highlighting the trade-offs in selecting an activation method for AC production. Additionally, this study highlights that CS-derived AC offers substantial energy savings of 78%, alongside a 75% reduction in carbon emissions and an 80% decrease in fossil depletion compared to coal-based AC. Overall, the synthesized AC shows promise as a sustainable alternative to coal-based counterparts. Full article

With global climate challenges intensifying, the cement industry, as a major CO₂ emitter, has attracted significant attention regarding its emission reduction potential and strategies. Advanced economies like the European Union use carbon pricing to spur innovation, while emerging countries focus on incremental solutions, such as fuel substitution. Combining LMDI decomposition and the LEAP model, this study examines Jiangsu Province as a test bed for China’s decarbonization strategy, a highly efficient region with carbon intensity 8% lower than the national average. Historical analysis identifies carbon intensity, energy mix, energy intensity, output scale, and economic effects as key drivers of emission changes. Specifically, the reduction in cement production, real estate contraction, lower housing construction, and reduced production capacity are the main factors curbing emissions. Under an integrated technology strategy—including energy efficiency, fuel and clinker substitution, and CCS—CO₂ emissions from Jiangsu’s cement sector are projected to decrease to 17.28 million tons and 10.9 million tons by 2060 under high- and low-demand scenarios, respectively. Clinker substitution is the most significant CO₂ reduction technology, contributing about 60%, while energy efficiency gains contribute only 3.4%. Despite the full deployment of existing reduction methods, Jiangsu’s cement industry is expected to face an emissions gap of approximately 10 million tons to achieve carbon neutrality by 2060, highlighting the need for innovative emission reduction technologies or carbon trading to meet carbon neutrality goals. Full article

Nuclear energy has a great impact on the global energy mix. In Spain, it supplies over 20% of current energy requirements, demonstrating the relevance of nuclear power plants. These plants generate different types of waste (apart from radioactive) that should be managed. For instance, the activated carbon included in filters (which neutralize isotopes in a possible radioactive leakage) should be periodically replaced. Nevertheless, these activated carbons might present long service lives, as they have not undergone any adsorption processes. Consequently, a considerable amount of activated carbon can be reused in alternative processes, even in the same nuclear power plant. The aim of this work was to assess the use of activated carbons (previously included in filters to prevent possible radioactive releases in primary circuits) for water treatment derived from the steam cycle of a nuclear power plant. A regeneration process (boron removal) was carried out (with differences between untreated carbon and after treatments, from S_BET = 684 m² g⁻¹ up to 934 m² g⁻¹), measuring the adsorption efficiency for ethanolamine and triton X-100. There were no significative results that support the adsorption effectiveness of the activated carbon tested for ethanolamine adsorption, whereas a high adsorption capacity was found for triton X-100 (q_L1 = 281 mg·g⁻¹), proving that factors such as porosity play an important role in the specific usage of activated carbons. Full article

This study focused on developing a novel composite phosphate-selective electrode for on-site and real-time applications using a silver polyglutaraldehyde phosphate and carbon nanotube (CNT) matrix. CNT-silver polyglutaraldehyde phosphate compound was synthesized and characterized using Fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), X-ray diffraction (XRD), and thermogravimetric analysis (TGA). The potentiometric performance of the composite phosphate-selective electrode was then investigated. The results demonstrated that the composite phosphate-selective electrode exhibited good sensitivity, with a linear response in the concentration range of 1.0 × 10⁻⁴ to 1.0 × 10⁻² M for phosphate ions. The electrode also showed high selectivity towards phosphate ions compared to other anions, such as chloride and nitrate. Additionally, the electrode displayed a quick response time of less than 15 s, making it suitable for real-time measurements. The electrode was applied to surface and soil water samples. The results obtained from the water samples showed a strong correlation with those obtained from the preferred spectrophotometry method, highlighting the potential of the developed electrode for on-site and continuous monitoring of phosphate and offering an efficient and practical solution for various fields that require phosphate detection. Full article

Fullerenes are a class of highly symmetric spherical carbon materials that have attracted significant attention in optoelectronic applications due to their excellent electron transport properties. However, the isotropy of their spherical structure often leads to disordered inter-sphere stacking in practical applications, limiting in-depth studies of their electron transport behavior. The successful fabrication of long-range ordered two-dimensional fullerene arrays has opened up new opportunities for exploring the structure–activity relationship in spatial charge transport. In this study, theoretical calculations were performed to analyze the effects of different periodic arrangements in two-dimensional fullerene arrays on electronic excitation and optical behavior. The results show that HLOPC₆₀ exhibits a strong absorption peak at 1050 nm, while TLOPC₆₀ displays prominent absorption features at 700 nm and 1300 nm, indicating that their electronic excitation characteristics are significantly influenced by the periodic structure. Additionally, analyses of orbital distribution and the spatial electron density reveal a close relationship between carrier transport and the structural topology. Quantitative studies further indicate that the interlayer interaction energies of the HLOPC₆₀ and TLOPC₆₀ arrangements are −105.65 kJ/mol and −135.25 kJ/mol, respectively. TLOPC₆₀ also exhibits stronger dispersion interactions, leading to enhanced interlayer binding. These findings provide new insights into the structural regulation of fullerene materials and offer theoretical guidance for the design and synthesis of novel organic optoelectronic materials. Full article

This study investigates the potential of graphene-based additives to improve the mechanical properties of compacted soil mixtures in rammed-earth construction, contributing to the development of environmentally friendly building materials. Two distinct soils were selected, combined with sand at optimized ratios, and treated with varying concentrations of a graphene liquid solution and a graphene-based paste (0.001, 0.005, 0.01, 0.05, and 0.1 wt.% relative to the soil-sand proportion). The effects of these additives were analyzed using the modified Proctor compaction and unconfined compressive strength (UCS) tests, focusing on parameters such as optimum water content (OWC), maximum dry density (MDD), maximum strength (q_u), and stiffness modulus (E). The results demonstrated that graphene’s influence on compaction behavior and mechanical performance depends strongly on the soil composition, with minimal variation between additive types. In finer soil mixtures, graphene disrupted particle packing, increased water demand, and reduced strength. In silt–sandy mixtures, graphene’s hydrophobicity and limited interaction with fines decreased water absorption and preserved density but likewise led to diminished strength. Conclusions from the experiments suggest a possible interaction between graphene, soil’s finer fraction, and potentially the swelling and non-swelling clay minerals, providing insights into the complex interplay between soil properties. Full article

N-containing carbon-based materials have been employed with claimed improved performance as an adsorbent of acidic molecules, volatile organic compounds (VOC), and metallic ions; catalyst; electrocatalyst; and supercapacitor. In this context, the present work provides valuable insights into the preparation of N-doped activated carbons (ACs) by thermal treatment in NH₃ atmosphere (ammonization). A commercial AC was submitted to two kinds of pretreatment: (i) reflux with dilute HNO₃; (ii) thermal treatment up to 800 °C in inert atmosphere. The original and modified ACs were subjected to ammonization up to different temperatures. ACs with N content up to ~8% were achieved. Nevertheless, the amount and type of inserted nitrogen depended on ammonization temperature and surface composition of the starting material. Remarkably, oxygenated acidic groups on the surface of the starting material favored nitrogen insertion at low temperatures, with formation of mostly aliphatic (amines, imides, and lactams), pyridinic, and pyrrolic nitrogens. In turn, high temperatures provoked the decomposition of labile aliphatic functions. Therefore, the AC prepared from the sample pre-treated with HNO₃, which had the highest content of oxygenated acidic groups among the materials submitted to ammonization, presented the highest N content after ammonization up to 400 °C but the lowest content after ammonization up to 800 °C. Full article

Enzymes play a vital role in various industrial sectors and are essential components of many products. Hybrid enzyme-polymeric capsules were developed using polysulfone-activated carbon capsules as scaffolds. The polysulfone-activated carbon capsules with an average diameter of 2.55 mm were fabricated by applying a phase inversion precipitation method. An increase in the amount of immobilized enzymes was observed with growth of activated carbon amount in polysulfone matrix. Enzyme immobilization was confirmed by the Bradford method, while Viscozyme^® L activity in carboxymethyl cellulose hydrolysis to glucose was measured by the Reducing Sugar DNS method. The recycling of the hybrid Viscozyme^® L-polysulfone/activated carbon capsules, and their reuse for subsequent cellulose hydrolysis was investigated and demonstrated repeatability of results. Full article

Nanoparticles with aerodynamic diameters of less than 100 nm pose serious problems to human health due to their small size and large surface area. Despite continuous progress in materials science to develop air remediation technologies, efficient nanoparticle filtration has appeared to be challenging. This study showcases the great promise of MXene-coated polyester textiles to efficiently filter nanoparticles, achieving a high efficiency of ~90% within the 15–30 nm range. Using alkaline earth metal ions to assist textile coating drastically improves the filter performance by ca. 25%, with the structure–property relationship thoroughly assessed by electron microscopy and X-ray computed tomography. Such techniques confirm metal ions’ crucial role in obtaining fully coated and impregnated textiles, which increases tortuosity and structural features that boost the ultimate filtration efficiency. Our work provides a novel perspective on using MXene textiles for nanoparticle filtration, presenting a viable alternative to produce high-performance air filters for real-world applications. Full article

This study focuses on fabricating flexible multi-junction diodes using carbon nanotubes (CNTs) as the base material, employing doping engineering and recrystallization-driven thermal diffusion techniques to enhance optoelectronic and thermoelectric properties. N-type CNTs are synthesized through ammonia doping and combined with intrinsic P-type CNTs to create PN multi-junction “buckypaper”. Post-diffusion processes improve junction crystallinity and doping gradients, significantly boosting the rectification ratio and optoelectronic and thermoelectric response. The device follows the superposition principle, achieving notable increases in thermoelectric and photovoltaic outputs, with the Seebeck coefficient rising from 5.7 μV/K to 24.4 μV/K. This study underscores the potential of flexible carbon-based devices for energy harvesting applications and advancing optoelectronic and thermoelectric systems. Full article